Fenix LD75C Multi-Spectrum LED Flashlight (White, Blue, Red, Green)

Description

The powerful and versatile Fenix LD75C Multi-Spectrum LED Flashlight (White, Blue, Red, Green) is loaded with features and is ideally suited for law enforcement, military and search & rescue professionals or outdoor enthusiasts. This illuminator uses four white Cree XM-L2 U2 LEDs to produce five outputs from a task-orientated 40 lumen economy output to a darkness-obliterating 4200-lumen turbo mode. In addition to the white emitters, there is a secondary LED that emits blue, red, and green light to perform tasks without interfering with night-adjusted vision, plus a secondary 200-lumen white output. Adding to the LD75C's versatility is a 4200 lumen disorientating strobe, and two coloured flashing modes that can be used for signalling. The light's switching system enables users to combine the white and coloured lights to customise the light signature for easier identification.

Multiple safety and power features protect the light and optimise the power output based on the battery charge and conditions. The output is digitally regulated to maintain consistent beam intensity throughout the battery charge to prevent dimming. Thermal control circuitry optimises the output based on temperature fluctuation to further maintain a consistent beam. Specialised circuitry monitors the internal temperature and automatically steps the output down to prevent damage due to excessive heat, while reverse polarity protection prevents damage to the light if the batteries are installed incorrectly. For full functionality, the light runs on four 18650 or eight CR123 batteries, but in a pinch it can operate with two 18650 or four CR123 batteries but with reduced outputs and runtimes depending on the light colour and mode selected.

Complementing the multiple light outputs is a housing that is built to withstand years of use. Its aluminium alloy body has a scratch and corrosion-resistant type III hard anodised finish, with a scratch-resistant tempered reflector window that has a anti-reflection coating to maximise light transmission. A sturdy and strong stainless steel bezel ring protects the head and lens from damage due to drops and impacts. The light is impact resistant to 1.0 m and IPX8-rated making it fully submersible to 2.0 m for up to 30 minutes. A ribbed handle provides a slip-resistant grip when using the light with gloves or in cold and wet conditions.

Key Features:

Primary White Light

• Eco: 40 lumen
• Low: 200 lumen
• Moed: 600 lumen
• High: 1800 lumen
• Turbo: 4200 lumen
• Four primary white Cree XM-L2 U2 LEDs
• Disorientating/signal white 4200-lumen strobe

Secondary Coloured Lights

• Blue: 45 lumen
• Red: 140 lumen
• Green: 190 lumen
• Cree XM-L RGB coloured LED
• Red light used for reading and tasks without affecting night adjusted vision
• Green is easier to see than red light, and is invisible to many game species
• Blue light shows fluid/blood trails for tracking
• Secondary LED also provides 200 lumens of white light
• Flashing modes: Flashing red signal, alternating flashing red and blue warning signal

Switching

• Location: Body
• Type: Three pushbuttons
• Momentary and constant-on modes
• Front-right button controls primary output on/off and output intensities
• Front-left button controls secondary light on/off, colour, and modes
• Rear button provides instant access to white strobe and momentary activation
• Simultaneous white and coloured light activation for custom signal or identification
• Intelligent last-mode memory switch

Construction

• Lightweight and durable aluminium alloy housing
• Scratch and corrosion-resistant Type III hard anodised finish
• Anti-reflection coated scratch-resistant tempered glass window
• IPX8-rated submersible, impact resistant to 2.0 m for up to 30 min
• Impact-resistant to 1.0 m
• Ribbed handle provides slip-resistant grip
• Heat dissipating fins machined into head
• Strong and durable stainless steel bezel ring protects against drops and impacts
• Power level indicator

Electronics

• Digitally regulated output maintains consistent beam intensity throughout battery charge
• Thermal control circuitry optimises output based on temperature fulgurations
• Overheat protection circuitry automatically steps power output down to avoid damage to the light
• Reverse-polarity protection prevents damage to light if batteries are installed incorrectly

Power

• Runs on four 18650 li-ion rechargeable batteries
• Capable of running on eight CR123 lithium batteries, but with reduced output and rutimes
• Flexible power options
• Can operate on two 18650 or four CR123
• With half the batteries, the corresponding primary LEDs will operate with same runtime but output is reduced by 50%
• Secondary LEDs maintain output intensity but runtime is reduced by 50%