SHAPE Complete Rig System for Select RED Cameras
Features
- Universal Baseplate Accomodates Varying Rig Sizes
- Height-Adjustable Rod Clamp
- Built-in Storage Areas
- Telescopic Handles with ARRI Rosettes
- Follow Focus Pro
Description
The Complete Rig System from SHAPE is a camera support system designed for RED WEAPON EPIC-W, SCARLET-W, and RAVEN cameras. It includes the REVOLT VCT universal baseplate, a top plate with extendable top handle, a pair of telescopic handles compatible with ARRI rosettes, a 4 x 5.6" (10.16 x 14.35 cm) matte box, and a snap-on follow focus unit. The follow focus snaps onto 15 mm rods, allowing for quick attachment, removal, and repositioning. The matte box features a swing-away system and two 4 x 5.6" (10.16 x 14.35 cm) rotating filter stages.
Featuring a sliding camera plate, SHAPE 's REVOLT VCT Universal Baseplate can accommodate rigs of varying sizes. Simply attach your camera via 1/4"-20 or 3/8"-16 screws to the top plate, and slide it onto the shoulder plate. Fore and aft movement allows you to balance the weight of your setup properly. Further adjustments can be made by moving the shoulder pad. The 15 mm rod clamps at the front and rear of the baseplate allow you to secure 15 mm accessories such as a matte box, follow focus, lens motors, lens supports, battery plates, or external recorders. Since the front rod clamp is attached to the top plate, the rod-mounted accessories don't need to be repositioned as the rig is adjusted. Additionally, handles can be mounted to the ARRI standard rosettes on either side of the plate. When not shoulder-mounted, the baseplate can be secured to a standard VCT-14 ENG quick release in a matter of seconds, saving time on set.
The black Telescopic Handles with ARRI Rosettes from SHAPE are left and right handgrips that can be attached to cameras and camera support hardware that has standard ARRI rosettes. Each arm features three points of articulation, combined with the approximately two inches of arm extension allows you to adjust the arms for your comfort. The arms attach to your camera or support via an ARRI compatible rosette with spring-loaded locking levers, which allow you to lock your arms in place without having a full 360° of rotation.
Shape's unique push-button articulating joint provides additional articulation near the rosette, while a second push-button articulation joint allows you to rotate and precisely position the rubber handgrips. A second spring-loaded locking lever along the arms allows you to extend the arms up to two inches and rotate the handgrips throughout 360°. The arms are indexed for extension and rotation, so you can quickly move between known setups.
This pair of Shape 15 mm Aluminium Rods (4") connect into your camera rig, extend it, and let you add various Shape and third-party accessories compatible with 15 mm rods. With these two rods and with a few fundamental accessories, you can most certainly even begin building your own rig from scratch.
The rods are each 15 mm in diameter, 4 inches ( 10 cm) long, hollow, non-threaded, and made of reliable aluminium coated with a clear finish.
This pair of Shape 15mm Aluminium Rods (8") connect into your camera rig, extend it, and let you add various Shape and third-party accessories compatible with 15 mm rods. With these two rods and with a few fundamental accessories, you can most certainly even begin building your own rig from scratch.
The rods are each 15 mm in diameter, 8 inches (20 cm) long, hollow, non-threaded, and made of reliable aluminium coated with a clear finish.
The top handle and top plate are designed to give you a solid and comfortable grip for the manipulation of your RED camera. The Push Button Arm with view finder bracket can easily be attached to the EVF mount of the top handle for an optimal setup of your RED camera rig. The handle grip frame is made from robust CNC machined aluminium and the finger grip is made from genuine Canadian maple wood for maximum comfort. You can quickly adjust and lock the handle length for an extension of approximately 3 inches (7.62 cm) from its original position in order to optimise the balance of your camera to your lens type.
The SHAPE Follow Focus Pro mounts on 15 mm rods and features an adjustable arm which puts the gear at the optimal position for the lens, no matter what the diameter is. The unit snaps onto 15 mm rods, allowing for quick attachment, removal, and re-positioning. Two 0.8 pitch gears come included and give you a choice of either 28 teeth or 43 teeth - depending on the throw distance of the lens. Additional features include two adjustable hard stops, removable marking disc, and an industry standard accessory port for using optional whips and cranks.
The 2-Stage 4 x 5.6" Matte Box from SHAPE can be used as a clip-on matte box or can be mounted on industry-standard 15 mm rod system. It is designed for light control, insertion, and adjustment of filters. It features a two-stage rotating 4 x 5.6" filter holder. The matte box accepts lenses with a front diameter up to 114 mm. It comes with six step-down rings that allow you to fit lenses with an outer diameter of 52, 58, 62, 67, 72, 77, and 82 mm as well.
Features
REVOLT VCT Universal Baseplate
- The sliding baseplate provides a quick positioning of your camera and accessories for an optimal adjustment of your camera's balance centre.
- Height-adjustable rod clamp for aligning the 15 mm rods at the proper LWS height in relation to the optical axis.
- Front and rear rod clamps allow you to extend your rig forwards and backwards.
- Built-in storage areas for extra screws and the Allen wrench ensure that necessary adjustment tools are always close at hand.
- Safety pins and spring-loaded levers prevent the top plate from sliding unintentionally.
- Soft and ergonomic shoulder pad.
Telescopic Handles with ARRI Rosettes (Black)
- The push-button locking joint enables independent rotation throughout 360°.
- Spring-loaded locking levers allow you to tighten or loosen the lever even when you do not have space to turn the lever throughout the entire 360° range.
- The arms feature two inches of extension and are indexed every 5 mm of extension.
- The arms can rotate through 360° and feature 30° of index markings.
Follow Focus Pro
- Snap-on 15 mm rod attachment
- Adjustable arm
- Two 0.8 pitch aluminium gears included: 28 teeth and 43 teeth
- Interchangeable gear position
- Adjustable hard stops
- Removable marking disc
- Industry standard accessory port
- CNC machined aluminium parts
Compatibility
Photo lenses with a minimum diameter of 52 mm
Professional video optics with up to 114 mm front diameter
- Includes 6 step-down rings (52 to 82, 58 to 82, 62 to 82, 67 to 82, 72 to 82, 77 to 82 mm)
- Made in Canada
Specifications
REVOLT VCT Universal Baseplate | |
Dimensions | 10.4 x 4.4 x 2" / 26 x 11 x 5 cm |
Weight | 1 kg |
Telescopic Handles with ARRI Rosettes (Black) | |
Load Capacity | 11 kg |
Dimensions | Arms Retracted: 4.3 x 13.0" / 10.8 x 33.0 cm Arms Extended: 4.3 x 15.0" / 10.8 x 38.1 cm |
Weight | Each Arm: 0.48 kg |
15mm Aluminium Rods (Pair, 4") | |
Diameter | 15 mm |
Length | 4 inches (10.1 cm) |
Material | Aluminium with a clear finish applied over it |
15mm Aluminium Rods (Pair, 8") | |
Diameter | 15 mm |
Length | 8 inches (20.3 cm) |
Material | Aluminium with a clear finish applied over it |
Top Plate Extendable Handle & EVF Mount for Select RED Cameras | |
General | |
Accessory Type | Top plate with handle and viewfinder bracket |
Width | 6 in / 15.24 cm |
Depth | 9.3 in / 23.62 cm |
Height | 9.8 in /24.89 cm |
Weight | 18.34 oz / 519.93 g |
Accessories | |
Intended For | Camcorder |
Features | Extendable handle |
Miscellaneous | |
Material | Aluminium |
Kit Content | |
Kit Content | (1) x top plate (1) x handle (1) x viewfinder bracket |
Follow Focus Pro | |
Construction Material | CNC machined black anodised aluminium |
Dimensions | 7.63 x 5.00 x 3.00" (19.37 x 12.70 x 7.62 cm) |
Weight | 0.6 kg |
2-Stage 4 x 5.6" Matte Box | |
Lens Fit and Mount | Fits lenses with front diameter up to 114mm Fits lenses with front diameter from 52 to 82mm (6 step-down rings included) |
Filter Type | 4 x 5.65" (10.16 x 14.35 cm) |
Total Filter Stages | 2 |
Rotating Stages | Endless |
Degree of Rotation | 360° |
Materials | Aluminium (lens holders are plastic) |
Dimensions | 11.5 x 7.5 x 3.5" (29.2 x 19.1 x 8.9 cm) |
Weight | 1.1 kg |
In The Box
- REVOLT VCT Universal Baseplate
- Telescopic Handles with ARRI Rosettes (Black)
- 15 mm Aluminum Rods (Pair, 4")
- 15 mm Aluminum Rods (Pair, 8")
- Top Plate Extendable Handle & EVF Mount for Select RED Cameras
- Follow Focus Pro
- 0.8 Pitch 28 Teeth Aluminium Gear for Follow Focus Pro
- 0.8 Pitch 43 Teeth Aluminium Gear for Follow Focus Pro
- 2-Stage Bracket for 4 x 5.6" Rotary Filters
- Clip-On System
- 15 mm Bracket
- French Flag
- 2 x Side Wing
- 6 x Step-Down Ring
Reviews
(no ratings yet)Give it a quick rating:
Thanks for your rating!
Write a review
Details
- Product: SHAPE Complete Rig System for Select RED Cameras
- Manufacturer: Shape
- Model: RWKS
- SKU: RWKS
- RM Product #: 49795
- Compatible With: RED Weapon
- Compatible With: RED Raven
- Compatible With: RED Epic Weapon
- Compatible With: RED Scarlet Weapon
- Warranty: Click here for warranty terms view terms