Teradek Bolt 500 DSMC2 Wireless TX has been discontinued, here are some related products you might like:
Teradek Bolt 500 DSMC2 Wireless TX
Features
- Integrates with RED DSMC2 Cameras
- Transmits up to 500' Line of Sight
- Supports up to 1080p60 Resolution
- HDMI Input
- Zero Delay
Description
The Bolt DSMC2 is a RED camera module that features the same zero-delay wireless video of the renowned Bolt line. Bolt DSMC2 modules attach seamlessly to the back of RED DSMC2 cameras via pogo pin connections, with pass-through power and video to keep setups clean of cable-clutter and save time in prep.
Zero-Delay Video
Transmit pristine 1080p60 wireless video instantly to receivers up to 150m away.
Compatibility
Bolt DSMC2 modules are compatible with Bolt 500, XT and LT systems, along with a wide variety of unique receiver solutions like SmallHD’s 703 Bolt, Focus Bolt, and the universal Sidekick series.
What's in the box:
This set comes with 1 transmitter only. You will need a corresponding receiver to work with the transmitter.
- 1 x DSMC2 Guard
- 1 x Hex L key 2.5mm size 3-5/8" length
- 1 x Mini-USB (5pin) to USB - 18in Cable (Firmware Cable)
- 2 x Antenna 2dBi WIFI 2.4/5.8GHz (Small Antenna)
Video
- Video Inputs: 1 x HDMI monitor path from DSMC2 camera
- Video Outputs: 1 x HDMI (Type A)
- Sdi Ancillary Data Support: supports metadata, timecode, and start/stop flags
- Color Sampling: SDI: YCbCr 4:2:2, 8-bit, HDMI: RGB 4:4:4, 8-bit
- Delay Tx To Rx: <0.001sec (without format conversion)
Supported Resolutions
- Supported Resolutions: 1080p 23.98/24/25/29.97/30/50/59.94/60, 720p50/59.94/60
Video Processing
- Video Compression: visually lossless
- Video Format Conversion Support: Yes
- Colour Correction: CDL/1024 1D LUT (supports 10-bit colour), 33x33x33 3D LUT (supports 10-bit colour)
Audio Processing
- Audio Compression: 48kHz 24-bit PCM
Inputs
- Audio Input: Embedded Audio Input
Physical
- Dimensions: 106.71mm x 63.68mm x 20.54mm (4.2" x 2.5" x 0.81")
- Weight: 226g
- Construction: Milled Aluminium(Chassis) and regulation-compliant PCB
- Mount-ability: Mounts seamlessly onto the back of DSMC2 camera
Interfaces
- Http: None
- Configuration Interfaces: None
- Switches: On/Off and Reset Switch
- Desktop App: Feature-rich Bolt Manager Application for OSX & Windows
- Usb Interface Functionality: Upgrade via Mini-USB
Network
- Wireless: Non-DFS Frequencies: US: 5.19 ~ 5.23 GHz and 5.755 ~ 5.795 GHz, EU & JP: 5.19 ~ 5.23 GHz
- DFS Frequencies: US: 5.27 ~ 5.55 GHz and 5.67 GHz, EU & JP: 5.27 ~ 5.67 GHz
- Rf Channel Selection: Auto
- Encryption: AES-128
- Rf Power: 17 dbm EIRP (with two 2dbi antennas)
- Range: Up to 150m line of sight
- Unicast Multicast: Unicast/Multicast
- Noise Rejection: Can coexist with WiFi and 5GHz cordless phones
Power
- Power Input: DSMC2 rear pogo connector
- Battery: None
- Nominal Power Consumption: 7.5 Watts (Measured at 1080p60)
Environmental
- Operating Temperature: 0 ~ 40 deg-C
Disclaimer: While operational, the Bolt DSMC2 uses the camera’s HDMI monitor path which prohibits the ability to use the RED EVF and a RED touchscreen LCD at the same time.
Specifications
Wireless | |
Wireless Range | 500' / 152.4 m (Line-of-Sight) |
# of Channels | 11 (40 MHz) |
Channel Bandwidth | 40 MHz |
Frequency Range | Non-DFS Frequencies US, JP, EU: 5.19 to 5.23 GHz US: 5.75 to 5.79 GHz DFS Frequencies US: 5.27 to 5.55 GHz US: 5.67 GHz JP, EU: 5.27 to 5.67 GHz |
Latency | < 1 ms |
RF Power | 17 dBm |
Wireless Video Compression | Compressed |
Interfaces | |
Antenna Ports | 2 x RP-SMA |
Video Connectors | 1 x HDMI Input 1 x HDMI Output |
Embedded Audio | HDMI |
Encryption | 128-Bit AES |
Format Support | |
Broadcast System Compatibility | NTSC, PAL |
Video Format | HDMI: 1080p 4:4:4 RGB 8-Bit at 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 fps 720p 4:4:4 RGB 8-Bit at 50, 59.94, 60 fps |
Audio Format | PCM Audio |
Video Standard Compliance | SMPTE 259M/274M/296M/372M/424M-B/425M |
Timecode | Yes |
LUT Support | None |
Power | |
Power Connector | 1 x RED DSMC2 POGO Input/Output |
Power Consumption | Device: (7.5 W) |
Environmental | |
Operating Temperature | 32 to 104°F / 0 to 40°C |
General | |
Mounting | 4 x M4 Male |
Materials | Aluminium |
Dimensions | 4.2 x 2.5 x 0.81" / 10.67 x 6.35 x 2.06 cm |
Weight | 8 oz / 226.8 g |
In The Box
- Teradek Bolt 500 DSMC2 Wireless TX
- DSMC2 Guard
- Antennas
- USB Type-A to Mini Cable (18")
- 2.5mm Allen Wrench
Reviews
(no ratings yet)Give it a quick rating:
Thanks for your rating!
Write a review
Details
- Product: Teradek Bolt 500 DSMC2 Wireless TX
- Manufacturer: Teradek
- Model: 10-0939
- SKU: 10-0939
- RM Product #: 69217
- Warranty: 1 year manufacturer warranty