dB Technologies VIO L212 Line-Array Module has been discontinued, here are some related products you might like:
dB Technologies VIO L212 Line-Array Module
Features
- 3-way active line array system.
- 3200W RMS digipro G4 AMP technology.
- Full range smps with pfc.
- Horn-loaded midrange for improved acoustic efficiency and coverage accuracy.
- Exclusively designed waveguide for maximum hf directivity control.
- Advanced dsp featuring linear phase fir filters.
- Acoustic compatibility with vio l210 used as down-fill.
- Modular slot for network and digital audio expansion cards (rdnet card installed).
- NFC + front led identification system.
- System test for quick transducers diagnostics.
- IPOS intelligent power-on sequence.
- Rubber magnetic raincover included.
- Only 52.9 kg per module.
- Built-in inclinometer.
Description
The dB Technologies VIO L212 Line-Array Module is a three-way active line array module exclusively equipped with neodymium components: 2×12″ woofers (3” v.c.) placed to the outsides in a dipolar arrangement provide an accurate transient response and an extended and controlled low-end reproduction; The mid-range section is mounted in the centre of the cabinet in a horn-loaded configuration which dramatically contributes to the system’s acoustic efficiency. Midrange frequencies are delivered by 4x 6.5” woofers (voice coil 2”), while the 2×1,4” neodymium compression drivers (voice coil 3”) have been mounted to a waveguide which contributes to create a cylindrical wavefront, much to the advantage of the system’s intelligibility and throw capabilities.
Each dBTechnologies VIO-L212 Line Array Subwoofer System acoustic engine is driven by 2 Digipro G4® Class-D 1600W amplifiers, providing each system with a total of 3200W RMS. The switched mode power supply is equipped with PFC (Power Factor Corrector) which greatly improves the efficiency of the system. Performances of the amplifier are very stable and consistent, regardless of the quality of the mains and fluctuations. This also grants a worldwide compatibility of the power supply (from 100V to 240V 50/60Hz) and limits power consumption.Furthermore, the power supply is 380V resistant, so the final amplifiers will be switched off in case of an undesired strike of 380V current, saving them from any damage.
The amp allows users to run system-test on electronics and transducers before and after use and a real time impedance control. The preamplifier’s floating audio input design grants a digital optical isolation between earth ground from the mains ant the audio ground flowing into the preamplifier board. This galvanic isolation greatly improves resistance to interferences and any unwanted buzzing and noises. The USB port allows firmware upgrades and diagnostics analysis, by downloading telemetry data on system performances and failures. Exclusive technology of VIO L212 amplifier is IPOS (Intelligent Power-On Sequence), a circuit that controls the sequence in which the main power supplies of all units within an array ramp up. As a result, each module is switched on in a different time frame, keeping the overall system’s inrush current low, even in very big PA system deployments.
Specifications
Technical Data | |
Speaker Type | 3-Way Active Line Array Module |
Acoustical Data | |
Usable Bandwidth | [- 6 dB]55 - 18.600 Hz |
Max SPL | One Unit: 142 dB |
HF | 2 x 1.4”, 3” v.c. - Neodymium |
MF | 4 x 6.5” , 2” v.c. - Neodymium |
LF | 2 x 12”, 3” v.c. - Neodymium |
Horizontal Directivity | 90° |
Vertical Directivity | depends on array size and configuration |
Amplifier | |
Amplifier | 3200 W RMS [2x 1600 W RMS bi-amped Class-D Digipro® G4] |
Cooling | Convection, Internal fan |
Power Supply | Full-range SMPS with PFC (100V-240V, 50-60Hz) |
Processor | |
Controller | DSP 32 bit |
AD/DA Converter | 24 bit/96 kHz |
Limiter | Dual Active Multiband Peak, RMS, Thermal |
Processing (filters) | FIR Linear Phase |
Input | |
Signal Input | 1x XLR female, balanced |
Signal Output | 1x XLR male, balanced |
Expansion Card | RDNet Card (1x RJ45 IN 1x RJ45 Link) |
Dante Card [Optional] | |
Power Socket | 1x PowerCON TRUE1 In |
1x PowerCON TRUE1 Out | |
Controls | 1 x Speaker Coupling (7 presets) |
1 x High pass filter Rotary Encoder (8 presets) | |
1 x HF Compensation (8 presets) | |
1 x System Test Button | |
Special Features | NFCTM and Frontal LED Identification System |
380V Resistant SMPS | |
IPOS Intelligent Power-On Sequence | |
Opto-isolated floating pre-amp | |
System Test (transducers diagnostics) | |
Inclinometer | |
Mechanics | |
Housing | Multiplex plywood - Polyurea painting |
Housing Design | Trapezoidal |
Handles | 4 x handles (2 on each side) |
Rain Cover | Included [Rubber magnetic] |
Rigging Points | 3 points rigging hardware |
Width | 1100 mm (43.31 in) |
Height | 380 mm (14.96 in) |
Depth | 450 mm (17.72 in) |
Weight | 54.4 Kg (119.93 lbs) |
In The Box
- dB Technologies VIO L212 Line-Array Module.
Reviews
(no ratings yet)Give it a quick rating:
Thanks for your rating!
Write a review
Details
- Product: dB Technologies VIO L212 Line-Array Module
- Manufacturer: dB Technologies
- Model: 1030102430
- SKU: 1030102430
- RM Product #: 70125