Studio Monitors

• 2-way bass-reflex bi-amplified nearfield studio monitor
• 5" cone woofer and 1" dome tweeter
• 54Hz - 30kHz frequency response
• 45W LF plus 25W HF bi-amp system for total 70W power amplification
• ROOM CONTROL and HIGH TRIM response controls
• XLR and TRS phone jack inputs, balanced or unbalanced

• 95W Total Output
• 165 mm Cone Woofer
• 25 mm Dome Tweeter
• Room Control Response Switch
• High Trim

• Analogue Stereo Volume Control
• Fits Any Active Speaker Setup
• Minimum of Clutter and Wires
• High-Precision Level Control
• No Power Required

• Universal stand for studio near-field monitors and wide range of loudspeakers
• Perfect for recording studios and listening environments
• Large 23 cm x 23 cm metal platform with soft rubberised padding reduces vibration
• Precise height adjustment in 5 steps from 30 cm up to 51 cm of elevation
• Heavy-duty steel construction for maximum weight capacity of 8.17 kg
• Floor base length of 24 cm per side

Supports Most Speakers up to 10 lb, 1/4"-20 Threaded Mounting to Speakers, Up to 27° of Tilt Adjustment, Up to 180° of Swivel Adjustment

Anodized Aluminum Construction, Integrated Cable Management, 34" High, For the Sonos One, PLAY:1, or PLAY:3, Horizontal/Vertical Placement of PLAY:3

• 95W Total Output.
• 165 mm Cone Woofer.
• 25 mm Dome Tweeter.
• Room Control Response Switch.
• High Trim.

Works with the Sonos One, PLAY:1, PLAY:3, Supports Wireless Speakers up to 10 lb, ±66° of Swivel with the Sonos One, ±66° of Swivel with Sonos PLAY:1

• 180-Watt Bridge-Mode Amplifier
• Long-Throw 10" Woofer
• Advanced Waveguide
• XLR and RCA Input Connectors
• Low-Pass Filter for Crossover Alignment

• Loaded with the same transparent audio circuitry as Drawmer's high-end offerings
• Streamlined design is tailor-made for smaller project studios
• Accommodates two sets of studio monitors and a subwoofer
• Built-in headphone amplifier with dedicated level control
• 3 inputs including 2 TRS jacks and a 1/8" auxiliary jack

Works with the Sonos One, PLAY:1, PLAY:3, Supports Wireless Speakers up to 10 lb, ±66° of Swivel with the Sonos One, ±66° of Swivel with Sonos PLAY:1

Exclusively for Use with the Sonos Beam, Works with Mounts for 37 to 70" Displays, Interfaces with Your Display Mount, Broad VESA Compatibility

For the Sonos One, One SL, or PLAY:1, Supports Other Devices up to 10 lb Total, Above-Outlet Installation, Integrated Cable Management

For the Sonos One, PLAY:1, or PLAY:3, Horizontal or Vertical Speaker Placement, Speaker Cable Management, Adjustable Height from 26 to 42"

Anodized Aluminum Construction, Integrated Cable Management, 34" High, For the Sonos One, PLAY:1, or PLAY:3, Horizontal/Vertical Placement of PLAY:3

• Supports Speakers up to 25 lb
• Metal Construction
• Speaker Cable Management
• Speaker Bolt-Mounting Option
• 34" High
• Universal Compatibility

Supports Speakers up to 25 lb, Metal Construction, Speaker Cable Management, Speaker Bolt-Mounting Option, 30" High, Universal Compatibility

• 120W Total Output.
• 203 mm Cone Woofer.
• 25 mm Dome Tweeter.
• Room Control Response Switch.
• High Trim.

• Solid and stable wall mount
• Adjustable boom
• 210 to 340 mm clamping range
• 200mm in width

• Titltable, Stable Shelf for Monitors
• 12.5° Angle Adjustment Range
• Additional Stop Angle for Security
• Felt Pads for Noise Filtration
• Height Adjustable Range of 31.5 to 51.2"
• 10 Height Positions in 2" Increments